Nowadays, elevator decorative door jambs are very common. Then, what materials are usually used for elevator door jambs? They are basically stone elevator door jambs. There are two reasons for this: First, environmental protection. Traditional marble materials can experience the baptism of hundreds of years when used in buildings, but the stone resources will eventually be exhausted if kept mining. The stone plastic elevator sleeve is made of natural stone powder, PVC resin powder, chemical powder and other environmental materials under high temperature and high pressure, which wastes and exploits natural resources. And the stone plastic elevator sleeve solves the problem that natural stone joints are easy to breed.

二是便捷省心，采用石塑電梯套進行施工，表面花色也比較自然，雖然沒有天然大理石那般渾然天成，但石塑電梯套飾面經過UV光固化防護處理，紋理更加自然均勻，不會出現大面積色差。

Second, it is convenient and worry free. The stone plastic elevator sleeve is used for construction, and the surface design and color are also relatively natural. Although it is not as natural as natural marble, the stone plastic elevator sleeve finish is more natural and uniform after UV curing protection treatment, and there will be no large area of color difference.

石塑電梯門套在運用的過程中，需要注意的是：在做好墻面的處理石塑電梯埡口雖輕便，但也有一定的重量，可直接膠粘安裝，想要石塑電梯埡口安裝更快，就要在安裝材料前，將墻體處理平整，凹凸不平的地方可以用砂漿水泥抹平，這樣可以更好地工作效率，以及材料的使用。

During the application of the stone plastic elevator door jamb, it should be noted that the stone plastic elevator pass is light, but it also has a certain weight, which can be directly glued for installation. If you want to install the stone plastic elevator pass more quickly, you should smooth the wall before installing materials. The uneven places can be plastered with mortar and cement, which can improve the work efficiency and use of materials.

安裝加固用硅膠或者云石膠都能夠進行安裝，因?yàn)槭茈娞輬嚎诘氖褂貌⒉皇且粋€短期的產品，所以希望大家挑選口碑比的膠水，確保安裝的牢固度。拼接方法石塑電梯埡口的線條在轉角的地方，需要用木工的切割據，兩個豎線條各切頂端一個，安裝時注意拼接的方向。

Silica gel or marble glue for installation and reinforcement can be used for installation. Because the use of stone plastic elevator pass is not a short-term product, we hope you can choose the glue with a reputation ratio to ensure the firmness of installation. Splicing method: The line of Shisu elevator pass is at the corner, which needs to be cut by carpenters. The top of two vertical lines should be cut one at each end. Pay attention to the splicing direction during installation.

墻面預處理將墻面進行清潔處理，清理干凈的毛刺、浮沉，有坑洼的地方要使用發泡膠填平。如果要求比較高的工程，可以再墻面找平后再安裝一層細木工板，然后把線條和側板安裝在細木工板上就可以，這樣效果會更好。

Wall pre-treatment: clean the wall, remove the burrs, floating and sinking, and fill the potholes with styrofoam. For projects with high requirements, a layer of blockboard can be installed after the wall is leveled, and then the lines and side plates can be installed on the blockboard, which will have better effect.

為大家介紹河南睿之捷裝飾工程有限公司，睿之捷電梯門套分為：側面板、封口條、底板、門柱板四部分組成，是獲得證書的新型環保電梯門套，公司生產的門套整體美觀，性價比高，抗沖擊，防火，防水，綠色環保無味，色澤持久統一，安裝簡便。

Henan Ruizhijie Decoration Engineering Co., Ltd. is introduced. The door pocket of Ruizhijie elevator is divided into four parts: side panel, sealing strip, bottom plate and door post plate. It is a new type of environmental protection elevator door pocket that has obtained a certificate. The door pocket produced by the company is beautiful overall, cost-effective, impact resistant, fireproof, waterproof, green, tasteless, durable and uniform color, and easy to install.