擔心的問題：安裝的時候不知道師傅的步驟是什么

Worried issue: I don't know what the master's steps are during installation

大理石電梯門套施上門安裝施工步驟：

Construction steps for installing marble elevator door frames:

1.石材挑選：用比色法對石材的顏色進行挑選分類，安裝在同一面的石材顏色應一致，按設計圖紙及分塊順序?qū)⑹木幪枴?/p>

1. Stone selection: Use colorimetric method to select and classify the color of the stone. The color of the stone installed on the same side should be consistent, and the stone should be numbered according to the design drawings and block order.

2.墻面基層清理：清理墻面，裝好基層托架。，同時進行結構套方，找規矩，彈出垂直線和水平線。并根據設計圖紙和實際需要彈出安裝石材的位置線和分塊線。

2. Wall base cleaning: Clean the wall and install the base bracket., Simultaneously perform structural layout, find rules, and draw vertical and horizontal lines. And according to the design drawings and actual needs, mark the position lines and block lines for installing the stone.

3.打線：根據尺寸，打好施工線，石材安裝前要事先用經緯儀打擊大角兩個面的豎向控制線，**好彈在離大角500px的位置上，以便隨時檢查垂直掛線的準確線，保證順利安裝，并在控制線的上下作出標記。

3. Marking: According to the size, mark the construction line. Before installing the stone, use a theodolite to strike the vertical control line on both sides of the large angle, and mark it at a distance of 500px from the large angle to check the accuracy of the vertical hanging line at any time and ensure smooth installation. Mark the top and bottom of the control line.

4.安裝底層托架，把預先安排好的支托按上平線支在將要安裝的底層石板上面。支托要支承牢固，相互之間要連接好，也可和架子接在一起，支架安好后，順支托方向釘鋪通長的50mm厚木板，木板上口要在同一個水平面上，以保證石材上下面處在同一水平面上。

4. Install the bottom bracket and support the pre arranged support bracket on the bottom stone slab to be installed according to the upper horizontal line. The support bracket should be firmly supported and connected to each other, and can also be connected to the frame. After the bracket is installed, a 50mm thick wooden board should be nailed along the direction of the support bracket. The upper opening of the wooden board should be on the same horizontal plane to ensure that the upper and lower surfaces of the stone are on the same horizontal plane.

5.安裝連接構件：用設計規定的不銹鋼螺栓固定角鋼和平鋼板。調整平鋼板的位置，使平鋼板的小孔正好與石板的插入孔對上，固定平鋼板，用扳子擰緊。

5. Install connecting components: Use stainless steel bolts specified in the design to fix angle steel and flat steel plates. Adjust the position of the flat steel plate so that the small hole of the flat steel plate is exactly aligned with the insertion hole of the slate, fix the flat steel plate, and tighten it with a wrench.

6.大理石裝飾板材安裝：按照溝槽和構件找好位置，便可把底層面板靠角上的一塊就位。

6. Installation of marble decorative panels: Find the position according to the groove and components, and then place the bottom panel at the corner.

7.板面微調：安裝好大理石裝飾板材再調整水平度，如板面上口不平，可在板底的一端下口的連接平鋼板上墊一相應的雙股銅絲墊。調整垂直度，并調整面板上口的不銹鋼連接件的距墻空隙，直至面板垂直。

7. Fine tuning of the board surface: After installing the marble decorative board, adjust the levelness. If the upper opening of the board surface is uneven, a corresponding double stranded copper wire pad can be placed on the connecting flat steel plate at the lower end of the board bottom. Adjust the verticality and adjust the gap between the stainless steel connector at the top of the panel and the wall until the panel is vertical.

8.頂部裝飾板材的安裝：頂部一層面板除了按一般石板安裝要求外，安裝調整好，在結構與石板的縫隙里吊一通長的20mm厚木條，木條上平為石板上口下去250mm，吊點可設在連接鐵件上?？捎貌输X絲吊木條，木條吊好后，即在石板與墻面之間的空隙里放填充物，且填塞嚴實，防止灌漿時漏漿。

8. Installation of top decorative panels: In addition to following the general requirements for installing stone slabs, the top layer of panels should be installed and adjusted. A 20mm thick wooden strip should be hung in the gap between the structure and the stone slab, with the top of the strip being 250mm below the upper opening of the stone slab. The hanging point can be set on the connecting iron piece. Wooden strips can be hung with colored aluminum wire. After the wooden strips are hung, fill the gap between the stone slab and the wall tightly to prevent leakage during grouting.

本文由河北工地電梯門套上門安裝廠家友情奉獻.更多有關的知識請點擊:http://m.k2f3.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from the on-site installation manufacturer of elevator door frames at a construction site in Hebei For more information, please click: http://m.k2f3.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message